8000-1690-01, Rev. A
SENSORVISION PRODUCTS 1
SpeedDome
®
LT
Auto Pan Pro
rammin
SENSORVISION PRODUCTS
ABOUT THIS DOCUMENT
This document was developed to help you understand the
limitations associated with programming the Auto Pan feature
for SpeedDome LT. Unlike other SpeedDome products, the
SpeedDome LT does not support pattern programming.
Instead, the pattern programming function is used to program
the Auto Pan. Auto Pan is a smooth side-to-side movement of
the camera that is performed when the appropriate pattern
number is selected.
Each SpeedDome LT supports only one Auto Pan. However,
this Auto Pan can be re-programmed over and over again.
Programming Limitations
Before you attempt programming the Auto Pan, keep the
following limitations in mind:
•
Although it appears to have three Patterns available to
program, you can only program the Auto Pan feature for
Pattern 1 for VM 16 Plus, VM32 and VM 1. For VM 96,
you can only program the auto pan for the lowest pattern
number listed.
•
Any extraneous movements made during the Auto Pan
programming are ignored when the programming is
complete. Once the end point of the Auto Pan is set, the
result will be a smooth pan between the start point and the
end point of the Auto Pan.
•
Do not attempt to create an Auto Pan that is greater than
one revolution (360º) of the SpeedDome LT. The dome
will accept this pattern during programming; however, it
will not work when you attempt to run the pattern. The
starting point and the ending point must be less than one
revolution of the SpeedDome for the Auto Pan to work
properly.
•
If you attempt to program other patterns for the dome, the
system will take you through the motions of the
programming. However, the new Auto Pan will not be
saved. Do not attempt to program more than one Auto Pan
per SpeedDome LT.
•
If you need to re-program the Auto Pan for the dome, you
must select the original pattern number that was
programmed. Selecting another available Pattern number
will not change the previously programmed Auto Pan.
VM 16 Plus Auto Pan Programming
If your system is VM 16 Plus, use the following steps to
program the Auto Pan:
Note: You must use the Main T
OUCH
T
RACKER
®
to perform
Auto Pan programming.
1.
Use the number buttons to select the appropriate dome,
then press Camera.
2.
Move the camera until you see the starting point of the
Auto Pan you are programming.
3.
Press Menu, then select !"#$%&'()**"%+.
4.
Press number 1 on the keypad.
5.
Move the camera to the end point of the Auto Pan you are
programming, then press Next.
To run the Auto Pan you just programmed, press 1 then
Pattern. The dome will pan from side-to-side until a camera
command, such as tilt or zoom, is issued. To re-program the
Auto Pan, repeat steps 1 through 5.
VM 32 Auto Pan Programming
If your system is VM 32, use the following steps to program
the Auto Pan:
Note: You must use the primary T
OUCH
T
RACKER
®
to perform
Auto Pan programming.
1.
Use the number buttons to select the appropriate dome,
then press Camera.
2.
Move the camera until you see the starting point of the
Auto Pan you are programming.
3.
Press Menu, then select !"#$%&'()**"%+.
4.
Press number 1 on the keypad.
5.
Move the camera to the end point of the Auto Pan you are
programming, then press Next.
To run the Auto Pan you just programmed, press 1 then
Pattern. The dome pans from side-to-side until a camera
command, such as tilt or zoom, is issued. To re-program the
Auto Pan, repeat steps 1 through 5.
VM 1 Auto Pan Programming
1.
Press the MENU key to display the ,)-+',"+..
2.
Use the arrow keys to move the cursor to (%$/%)0'1$0",
then press ENTER.
3.
Press the SELC key until the number associated with the
SpeedDome LT appears.
4.
Move the cursor to (%$/%)0'()**"%+2, then press
ENTER.
Continued on next page
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals